|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Provisional Data Sheet No. PD - 9.1666A IRFE130 REPETITIVE AVALANCHE AND dv/dt RATED JANTX2N6796U (R) HEXFET TRANSISTOR JANTXV2N6796U [REF:MIL-PRF-19500/557] N-CHANNEL 100Volt, 0.18, HEXFET The leadless chip carrier (LCC) package represents the logical next step in the continual evolution of surface mount technology. The LCC provides designers the extra flexibility they need to increase circuit board density. International Rectifier has engineered the LCC package to meet the specific needs of the power market by increasing the size of the bottom source pad, thereby enhancing the thermal and electrical performance. The lid of the package is grounded to the source to reduce RF interference. HEXFET transistors also feature all of the well-established advantages of MOSFETs, such as voltage control, very fast switching, ease of paralleling and electrical parameter temperature stability. They are well-suited for applications such as switching power supplies, motor controls, inverters, choppers, audio amplifiers and high-energy pulse circuits, and virtually any application where high reliability is required. Product Summary Part Number IRFE130 BVDSS 100V RDS(on) 0.18 ID 8.0A Features: n n n n n n Hermetically Sealed Simple Drive Requirements Ease of Paralleling Small footprint Surface Mount Lightweight Absolute Maximum Ratings Parameter ID @ VGS = 10V, TC = 25C ID @ VGS = 10V, TC = 100C IDM PD @ TC = 25C VGS EAS dv/dt TJ TSTG Continuous Drain Current Continuous Drain Current Pulsed Drain Current Max. Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy Peak Diode Recovery dv/dt Operating Junction Storage Temperature Range Surface Temperature Weight IRFE130, JANTX-, JANTXV-, 2N6796U Units 8.0 A 5.0 32 25 W 0.17 W/K 20 V 134 mJ 8.3 V/ns -55 to 150 o C 300 ( for 5 seconds) 0.42 (typical) g 11/13/97 IRFE130, JANTX-, JANTXV-, 2N6796U Device Electrical Characteristics @ Tj = 25C (Unless Otherwise Specified) Parameter BVDSS Drain-to-Source Breakdown Voltage BVDSS/TJ Temperature Coefficient of Breakdown Voltage RDS(on) Static Drain-to-Source On-State Resistance VGS(th) Gate Threshold Voltage gfs Forward Transconductance IDSS Zero Gate Voltage Drain Current Min 100 -- -- -- 2.0 3.0 -- -- -- -- -- -- -- -- -- -- -- -- -- Typ Max Units -- 0.11 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1.8 4.3 -- -- 0.18 0.207 4.0 -- 25 250 100 -100 29 6.5 17 30 75 40 45 -- -- V V/C V S( ) A Test Conditions VGS =0 V, ID = 1.0mA Reference to 25C, ID = 1.0mA VGS = 10V, ID = 5.0A VGS = 10V, ID = 8.0A VDS = VGS, ID = 250A VDS > 15V, IDS = 5.0A VDS= 0.8 x Max Rating,VGS=0V VDS = 0.8 x Max Rating VGS = 0V, TJ = 125C VGS = 20 V VGS = -20V VGS = 10V, ID = 8.0A VDS = Max Rating x 0.5 VDD = 50V, ID = 8.0A, RG = 7.5 IGSS IGSS Qg Qgs Qgd td(on) tr td(off) tf LD LS Gate-to-Source Leakage Forward Gate-to-Source Leakage Reverse Total Gate Charge Gate-to-Source Charge Gate-to-Drain (`Miller') Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance Internal Source Inductance nA nC ns M a u e f o d i pdt e s r d r m ra n a o de. i ybl hw Modified MOSFET s m o s o ig te itra idcacs n h nenl nutne. nH Maue fo cne o esrd rm etr f suc pdt teedo ore a o h n f suc bnigwr o r e o d n i e. Ciss Coss Crss Input Capacitance Output Capacitance Reverse Transfer Capacitance -- -- -- 660 260 51 -- -- -- pF VGS = 0V, VDS = 25 V f = 1.0MHz Source-Drain Diode Ratings and Characteristics Parameter IS ISM VSD trr QRR ton Continuous Source Current (Body Diode) Pulse Source Current (Body Diode) Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time Min Typ Max Units -- -- -- -- -- -- -- -- -- -- 8.0 32 1.5 300 970 Test Conditions Modified MOSFET symbol showing the integral reverse p-n junction rectifier. Tj = 25C, IS = 8.0A, VGS = 0V Tj = 25C, IF = 8.0A, di/dt 100A/s VDD 50V A V ns nC Intrinsic turn-on time is negligible. Turn-on speed is substantially controlled by LS + LD. Thermal Resistance Parameter RthJC RthJPCB Junction-to-Case Junction-to-PC Board Min Typ Max -- -- -- -- 5.0 Units K/W Test Conditions 19 Soldered to a copper clad PC board Details of notes through are on the last page IRFE130, JANTX-, JANTXV-, 2N6796U Device 100 100 I D , Drain-to-Source Current (A) I D , Drain-to-Source Current (A) VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP VGS 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V TOP 10 10 4.5V 4.5V 1 1 0.1 0.1 20s PULSE WIDTH TJ = 25 C 1 10 100 0.1 0.1 20s PULSE WIDTH TJ = 150 C 1 10 100 VDS , Drain-to-Source Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics RDS(on) , Drain-to-Source On Resistance (Normalized) 100 2.5 I = 7.4A IDD = 8.0 A I D , Drain-to-Source Current (A) TJ = 25 C TJ = 150 C 2.0 10 1.5 1.0 1 0.5 0.1 4 5 6 7 V DS = 50V 20s PULSE WIDTH 8 9 10 0.0 -60 -40 -20 VGS = 10V 0 20 40 60 80 100 120 140 160 VGS , Gate-to-Source Voltage (V) TJ , Junction Temperature C) ( Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance Vs. Temperature IRFE130, JANTX-, JANTXV-, 2N6796U Device 1200 1000 VGS , Gate-to-Source Voltage (V) VGS = Ciss = Crss = Coss = 0V, f = 1MHz Cgs + Cgd , Cds SHORTED Cgd Cds + Cgd 20 ID = 8.0 A 7.4 16 V DS= 80V V DS= 50V V DS= 20V C, Capacitance (pF) 800 Ciss 12 600 Coss 400 8 200 4 Crss 0 1 10 100 0 0 6 12 FOR TEST CIRCUIT SEE FIGURE 13 18 24 30 VDS , Drain-to-Source Voltage (V) QG , Total Gate Charge (nC) Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage 100 1000 ISD , Reverse Drain Current (A) TJ = 25 C TJ = 150 C OPERATION IN THIS AREA LIMITED BY RDS(on) 100 10 I D , Drain Current (A) 10 1 1 0.1 0.2 V GS = 0 V 0.8 1.4 2.0 2.6 0.1 1 TC = 25 C TJ = 150 C Single Pulse 10 100 1000 VSD ,Source-to-Drain Voltage (V) VDS , Drain-to-Source Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage Fig 8. Maximum Safe Operating Area IRFE130, JANTX-, JANTXV-, 2N6796U Device 10.0 VDS VGS RD 8.0 D.U.T. + I D , Drain Current (A) RG -VDD 6.0 10V Pulse Width 1 s Duty Factor 0.1 % 4.0 Fig 10a. Switching Time Test Circuit 2.0 VDS 90% 0.0 25 50 75 100 125 150 TC , Case Temperature ( C) 10% VGS Fig 9. Maximum Drain Current Vs. Case Temperature td(on) tr t d(off) tf Fig 10b. Switching Time Waveforms 100 Thermal Response (Z thJC ) 10 D = 0.50 1 0.20 0.10 0.05 0.02 0.01 SINGLE PULSE (THERMAL RESPONSE) Notes: 1. Duty factor D = t 1 / t 2 2. Peak T J = P DM x Z thJC + TC 0.0001 0.001 0.01 0.1 1 P DM t1 t2 0.1 0.01 0.00001 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case IRFE130, JANTX-, JANTXV-, 2N6796U Device 400 EAS , Single Pulse Avalanche Energy (mJ) TOP BOTTOM 300 15 V ID 3.3A 5.0A 8.0A VD S L D R IV E R 200 RG 1 20V D .U .T IA S tp + - VD D A 0 .0 1 100 Fig 12a. Unclamped Inductive Test Circuit V (B R )D S S tp 0 25 50 75 100 125 150 Starting TJ , Junction Temperature ( C) Fig 12c. Maximum Avalanche Energy Vs. Drain Current IAS Fig 12b. Unclamped Inductive Waveforms Current Regulator Same Type as D.U.T. 50K 0 12V .2F .3F QG 10 V QGS VG QGD VGS 3mA D.U.T. + V - DS IG ID Charge Current Sampling Resistors Fig 13a. Basic Gate Charge Waveform Fig 13b. Gate Charge Test Circuit IRFE130, JANTX-, JANTXV-, 2N6796U Device Peak Diode Recovery dv/dt Test Circuit D.U.T + + Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer - + RG * * * * dv/dt controlled by RG Driver same type as D.U.T. ISD controlled by Duty Factor "D" D.U.T. - Device Under Test + VDD Driver Gate Drive P.W. Period D= P.W. Period VGS=10V * D.U.T. ISD Waveform Reverse Recovery Current Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt VDD Re-Applied Voltage Inductor Curent Body Diode Forward Drop Ripple 5% ISD * VGS = 5V for Logic Level Devices Fig 14. For N-Channel HEXFETS IRFE130, JANTX-, JANTXV-, 2N6796U Device Notes: Repetitive Rating; Pulse width limited by @ VDD = 50 V, Starting TJ = 25C, maximum junction temperature. EAS = [0.5 * L * (IL2) ] Refer to current HEXFET reliability report. Peak IL = 8.0A, VGS =10 V, 25 RG 200 Pulse width 300 s; Duty Cycle 2% K/W = C/W ISD 8.0A, di/dt 480 A/s, VDD BVDSS, TJ 150C Suggested RG = 2.35 Case Outline and Dimensions -- Leadless Chip Carrier (LCC) Package IR Case Style Leadless Chip Carrier (LCC) WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331 EUROPEAN HEADQUARTERS: Hurst Green, Oxted, Surrey RH8 9BB, UK Tel: ++ 44 1883 732020 IR CANADA: 7321 Victoria Park Ave., Suite 201, Markham, Ontario L3R 2Z8, Tel: (905) 475 1897 IR GERMANY: Saalburgstrasse 157, 61350 Bad Homburg Tel: ++ 49 6172 96590 IR ITALY: Via Liguria 49, 10071 Borgaro, Torino Tel: ++ 39 11 451 0111 IR FAR EAST: K&H Bldg., 2F, 30-4 Nishi-Ikebukuro 3-Chome, Toshima-Ku, Tokyo Japan 171 Tel: 81 3 3983 0086 IR SOUTHEAST ASIA: 315 Outram Road, #10-02 Tan Boon Liat Building, Singapore 0316 Tel: 65 221 8371 http://www.irf.com/ Data and specifications subject to change without notice. 11/97 |
Price & Availability of JANTX2N6796U |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |